My Friends,
It is now obvious to most people, that there are a Group of Clowns, that spread disinformation throughout the Free Energy Community! This group of Clowns, Lie about Energy Machines, to effectively Debunk, with Extreme Bias and Fakery, these machines, so as to make you think that these machines do not work, when in Point of Fact, they Do!
These industry Gurus, which lie to you all the time, never share any provable results to show where they get their information from, yet they report all sorts of Fakery and Lies to implement a sense of distrust throughout the community, an effective tactic for those that are still very unaware of what they are actually doing!
For many years now, we have consistently shown you this, and other tactics that they employ, to keep you from a Free Energy Future!
Know this; They all Worship Satan and think of you as Animals, this is known World Wide now, and most do not doubt this, especially when we have quotes from them saying this!
Floyd Sweet said:
The feedback loop: Previously mentioned, you will more clearly see how the loop functions at the time you see the physical construction of the stationary armature of stator assembly. The underlying principal (forget Millikan’s experiment) has been derived in that magnetic effects vary on the square of the current. As the load on the machine increases, the volt-ampere product increases. The rate of flow of charges increases. Quantum mechanics state not all electrons in copper are free to carry charges. Then it’s time to set the wheels in motion to free them from binding magnetic forces. Once this is done, conductivity will improve and resistance decrease as we are dealing only with electrons. Copper will not change to another metal as atoms which are mostly empty space would have many electrons to spare anyway.
Ref: Floyd Sweet - The Space-Flux Coupled Alternator
Yet, they will never go near this very simple Fact! They can not show you anything, factual, that refutes the basic fact that: 32 = 9, so in a Standing Wave, there is more energy in the Standing Wave, than in the original Wave by a factor of N Squared! The Conventional Electric "Generator" works on this very same principle!
It is important that "magnetic effects vary on the square of the current" is understood correctly, as Andrey Melnichenko also talks about this fact! This works two ways, Current and the Magnetic Field are the same basic things, only observed from different observational points!
Take three Permanent Magnets, each at: 3 Gauss, and stack them on top of each other, in additive direction, we get: 32 = 9 x 3 Gauss = 27 Gauss!
Remember, we have covered this before, 1 Gauss = 79.77 Amperes per meter, so, if we do the Math,
- 3 x 79.77 Amperes per meter = 239.31 Amperes per meter
- 3 Magnets x 239.31 Amperes per meter = 717.93 Amperes per meter
and now, if we use our known equation:
- 27 Gauss x 79.77 Amperes per meter = 2153.79 Amperes per meter.
The ampere per meter (symbolized A/m) is the International Unit of magnetic field strength. It is derived from basic standard units, but is expressed directly in base units and cannot be further reduced.
Consider the interior of a long, cylindrical coil with a single winding and an air core. Suppose that the linear current density in this coil is 1 ampere per meter of displacement as measured along the coil axis. (This expression differs from current density per unit area, which is expressed in amperes per meter squared .) Then the magnetic field strength in the interior of the coil is defined as 1 A/m.
For a given coil, the magnetic field strength is directly proportional to the linear current density. Thus, if the linear current density doubles, so does the magnetic field strength; if the linear current density becomes 1/10 as great, the magnetic field strength also diminishes by a factor of 10.
Sometimes, magnetic field strength is expressed in units called oersteds (symbolized Oe). The oersted is a larger unit than the ampere per meter. Approximate conversions are:
1 Oe = 79.578 A/m
1 A/m = 0.012566 Oe
Ref: ampere per meter (A/m, Oe, oersted)
Which converts to Joules per square Ampere:
Joule Per Square Ampere (J/A2) is a unit in the category of Electric inductance. It is also known as joule/square ampere. Joule Per Square Ampere (J/A2) has a dimension of ML2T-2I-2 where M is mass, L is length, T is time, and I is electric current. It essentially the same as the corresponding standard SI unit H.
Ref: Joule Per Square Ampere
And the So Called Guru's cant work this simple stuff out? Really? OMG!!! Not Berry Cleva after all hey?
So, Floyd Sweet was right, there is more Energy in a Team Wave, or a Standing Wave, as Andrey Melnichenko has also pointed out:
Total energy of a standing electromagnetic wave can be many times greater than the energy of waves and the electromagnetic field to add. As a result, the total energy of the system increases.
Ref: Andrey Melnichenko - Transgeneratsiya electromagnetic field energy
Remember this:
NOTE:
There can be 2 different methods to achieve a Standing Wave, Current can Stand:
Or the Magnetic Field can Stand. Remember what Floyd Sweet told us:
If the directions of the two signals are such that opposite H-fields cancel and E-fields add, an apparently steady E-field will be created. The energy density of the fields remain as calculated above, but the value of the E-field will double from E / 2 to E.
...
Similarly, if two signals flow through each other in such a way as to give the appearance of a steady magnetic field as a result of their E-field cancelling it is easily shown using the above equations to cancel out H and c...
Floyd Sweet was very clear about this!
They, the Clowns, will hide this from you all day long, because they do not want you to know this very simple, verifiable, stuff!
Why do they Fail, they Fail by Design!
In my haste to post this, I may have made an error, so please correct me if I have made a mistake!
Best Wishes,
Chris